Sold Out / discontinued! See Replacement-Engine ENG1395B (below or insert Number into Search-Field)!
 
Brand new Chevrolet 5,7 Liter V8 350CID (New Block! Not remanufactured!) 195-260PS (depends to attaching parts), established quality direct from General-Motors Performance Parts! GM 12681429
 
Engine reaches power level of 260HP equipped with 600CFM 4BBL Carburetor and Headers. Also as an excellent Spare Engine for Vehicles where Torque rather than Power is a Target (like Limousines, Pickups, etc.).
 
Manufacturer & Part Number: GM Performance Parts 10067353
 
There is a similar Engine available from GM (No 12499529) which reaches aprox. 290 HP max Power but much later - at 5100 RPM (compared to the offered Engine here at approx.4600 RPM!).
 
Engine is shipped complete as shown on Photos with Cylinder Heads, Valve Covers, Oil Pan, Timing Cover mounted. Comes fixed in a special Wood Pallet.
 
Technical Datas:
  • Engine Type: Chevrolet GEN-I (Valve Cover Bolts located at outer Edge of Valve Cover - no Centerbolt Valve Covers)
  • Years: 1969-1985
  • Size: 5,7 Liter (350 CID)
  • Bore & stroke: 4" x 3,47"
  • Compression Ratio: 8,5:1
  • Power: 195-260HP (ca. 143-191 kW) at +/- 4600 RPM (no exact Value given due to different Intake/Exhaust Equipment of Vehicle)
  • Torque: 474 Nm bei +/- 3700 RPM (no exact value given due to different equipment)
  • 4-Bolt Main Bearings
  • Cast iron Heads 76 cc
  • Intake & Exhaust Valves: 1,94 Einlass /1,5 Auslass
  • Camshaft: 194° Intake / 202° Exhaust @ 0,050"
  • Lifter: Hydraulic tappet
  • Rocker Arm: 1,5
  • Cast aluminum Pistons 
  • Nodular iron Crankshaft
  • Two Piece Rear Main Bearing Seal
  • Bolt Circle Mounting Bolts Crankshaft to Flywheel: 3,58"
  • Minimum fuel: 87 Octan
  • Oil Dipstick left or right possible (one Hole has to be plugged - plug is included)
  • Timing tabs included for 6-3/4" and 8" Balancers
  • Ignition Timing at Idle 10° BTDC (Vaccum disconnected), 32° total Advance.
Content: Engine as shown on Pictures, excluding attaching Parts and Gaskets to mount them (must be ordered separately - see below under "Could be also interesting for you...").
 
Which Gaskets do I need for an Engine Replacement?
In most Cases you need the following Gaskets (Suggestions):
Intake Manifold Gasket (excluding Engines which come with a new Intake Manifold already installed - check Photos))
Exhaust Manifold Gaskets (Position: between Cylinder Head and Exhaust Manifold)
Water Pump Gaskets (many GM V8 need 2 Pieces) (excluding Engines which come with an new Water Pump installed - see Photos!)
Ignition Distributor Mount Gasket (excluding Engines which come with a new Distributor already installed (see Photos) or Engines which which do not use a Distributor at all))
Fuel Pump Mount Gasket (only on older Models which still use mechanical Fuel Pump)
(Further Gaskets could be needed depending on Type and Model Year...)
You`ll find the Engines Gaskets in the Category "Gaskets, Seals & Gasket Sets"
 
Fits: Insert your Vehicles Datas and select respective Category.
 
The Engine can also be used as a Substitude for Chevrolet 305CID 5,0 Liter Engines (additional Parts like e.g. Carburetor etc.) may be needed. Note that there is another similar Engine available (ENG1394) that has a different Camshaft. Both Engines are intended as Spare Engines for all Vehicles with Small Block Engines Gen1 up to 1985. They of course can`t match all the different Details like different Camshafts, Pistons, Compression Ratio, etc. of theses different Vehicles and Models up to 1985.
 
NOTE: GM does not recommend this Engine to be used in Heavy Trucks (Due to Timing and resulting Power Curve/Emissions).
 
Fits: Insert your Vehicles Datas and choose respective Category.
 
REMAINDER ITEM - THEREAFTER DISCONTINUED! IF SOLD OUT SEE SUBSTITUDE ENG1395B !

CRATE ENGINE GM (CHEVROLET PERFORMANCE) 350CID / 195-260HP V8

Product number: ENG1395
0,00 €
  inkl. 19% VAT.
* incl. tax, plus shipping
no longer available